Call for proposals
Proposals are invited for observations with the Swedish LOFAR station, located at Onsala Space Observatory, in the period September 2017 – March 2018.
Deadline: Friday 5 May 2017 (23:59:59 UTC)
The Swedish LOFAR station, in the stand-alone configuration offered here, covers the frequency ranges 10–90 MHz and 110–240 MHz in two orthogonal linear polarisations. The maximum bandwidth is 100 MHz and can only be used for one of the frequency ranges mentioned above at a time.
Observing period and operations:
This Call for proposals is for the observing period 1 September 2017 – 31 March 2018. There are typically 1–2 days/week available for the stand-alone observations.
The telescope is open for scientists from all countries. Co-operation with Swedish scientists is encouraged (but proposals will be evaluated solely on scientific merit).
Observers are expected to visit Onsala to prepare the observations, which can be carried out remotely. The observations will require knowledge about how to use a LOFAR station in stand-alone mode (including how to write scripts to control the station) and how to handle the data.
There are several data products that can be recorded from the station:
1.) The high data rate streams:
Up to 244 synthesized beams in the form of complex wave data delivered as individual streams in UDP packets over a 3 Gbit/s connection. Each stream is a subband of width 195 kHz at a cadence of 5.12 µs. In the normal operations mode, the maximum bandwidth for the high data-rate output is 48 MHz if all streams are beam-formed in the same direction. Alternatively, in the other extreme case, 244 different beams can be formed but will then only cover 195 kHz of bandwidth. There is thus a trade-space between number of digital beams and bandwidth per beam.
(Note: In an alternative operations mode, the subbands are 156 kHz wide at a cadence of 6.4 μs, and the high data-rate output is 38 MHz.)
2.) Low-cadence visibilities:
Station visibility matrices can be dumped in files integrated over one second, but only for a single subband at a time.
3.) Low-cadence beam-formed data:
This is the total power of each data stream integrated over one second, dumped in files.
4.) Low-cadence antenna/tile total power:
These are the total powers in all 512 subbands (80 or 100 MHz) of each antenna or tile signal integrated over one second and dumped in files.
5.) Full array temporal burst data:
Triggered capture of complex waveforms from all antenna elements in the array at 200 MHz sampling up to 8 s in duration.
At Onsala, we offer the possibility to record the high data-rate streams in continuous runs of durations of up to a maximum of 48 h (in practice, to leave disk space for data reduction, not more than 36 hours is recommended). After that, it is up to the project team to promptly reduce the observation so that the raw data can be removed to free up memory for subsequent observations. Processing capacity on the computers storing the data is available (proposers should check with local contacts before submitting if this processing capability is sufficient for their needs). In addition to CPU processing, we also provide a GPU capable of processing 2 of out 4 data lanes in real-time.
For data recording and analysis (such as dedispersion), we provide several options including LuMP, DSPSR, PSRCHIVE, and TEMPO2. On-the-fly data reduction may be possible as well. State clearly in the proposal what software you would like to use in that case and how much it would reduce the footprint of the data needed to be stored.
Theoretical LOFAR sensititvity (rms noise level) for 1 hour integration time, an effective bandwidth of 6 MHz and dual polarisation. A weighting factor of 1.3 is applied.
Proposal preparation and submission:
The proposal must contain a front page with some basic information (see below), a proper and concise scientific justification including an explanation for how the requested observing time was estimated, in total no more than two A4 pages long, plus figures and tables if needed (for a total maximum of six pages, plus the front page).
The front page must contain:
- The title of the proposal.
- The date of the proposal.
- The name, affiliation, adress and email address of the principal investigator (PI).
- The names and affiliations of the co-investigators.
- The requested observing time.
- An abstract.
There is no template file available.